產品說明Product description:
LS-340型地坪研磨機主要用于大范圍地面粗效打磨，高效研磨處理，一機多用，能24小時工作等特點。外型美觀，采用全鋼制作，絕不會有斷裂，脫焊等現象，振動小，生手、熟手都可以操作。本機使用電機3kw，每個班可打磨毛地2000平方米，可研磨中涂4000平方米。LS-340 type floor grinding machine is mainly used for grinding a wide range of ground crude efficiency, efficient grinding processing, multi use of one machine, 24 hours to work. Appearance, the all steel production will never break, sealing off wait for a phenomenon, small vibration, novice, proficient and can operate. The machine using a 3KW motors, each class can be polished digitonin 2000 square meters, abrasive coated with 4000 square meter

用途 use ：

廣泛用于粗糙、不平整地面的修磨、清除混凝土地坪上的密封層及油漆和舊的環氧地坪翻新、膠脂等各種表面的修磨和處理。Widely used in rough, uneven ground repair, removal of the concrete floor of the sealing layer and paint and old epoxy floor renovation, ；rubber and grease and other surface repair and treatment.

使用方法  usage method：

l 硬水泥、水磨石地板，使用金剛磨盤(B)或(C)作基礎處理，如果有很松的水泥地板，可以用碳化硅磨盤(A)處理，這樣可以大大降低耗材成本；舊薄涂油漆地板可使用長方條合金盤(E)清除油漆。Hard cement, terrazzo floor, using diamond millstone (b) or (c) as the basis for treatment, if there is a very loose cement floor can treated with silicon carbide grinding disc (a), which can greatly reduce the cost of consumables; old thin coating paint floor can use rectangular bar alloy disc (E) removing paint.

l 刮完膩?zhàn)?/a>層可用碳化硅磨盤(A)進行打磨。如果地板要求高達到無痕，可使用鋁合金研磨盤(F)粘貼砂盤進行研磨效果更好。After scraping putty layer available silicon carbide grinding disc (a) polished. If the floor requirements up to no trace, the use of aluminum alloy grinding disc (f) paste sand disc grinding effect is better.

l 接電線請將插頭①號從插座上拔下，將插頭里面兩顆螺絲打開，一根粗銅柱為零線，其它三根為380V火線，如果接三根火線，零線不接，主機同樣可以工作，機座上多用插座無220V電源，但有火線，小心觸電，注意安全。Wiring please plug, from the socket unplug, will open the plug inside the two screws and a stout pillars for the zero line, the other three root is 380V wire, if three FireWire, zero line is not connected, the host can work as, seat multi-purpose socket without 220V power supply, but FireWire, beware of electric shock, pay attention to safety.

維修與保養Maintenance and maintenance：
在工作一段時間后，如果發現沒力，可以松開⑧號機座螺絲，調節④好皮帶調節螺絲；在工作出現經常自動斷電時，請檢查電線是否為國標4平方線，而且電線要完全拉開，不能盤在一起，在②號過載漏電保護開關里面有一條白色連接線，拔開檢查是否連接牢固。5、如果皮帶不松，電機轉動，但地盤不轉，有可能是皮帶輪松掉，請打開前蓋板重新安裝皮帶輪。機器如果有振動，請檢查地盤橡膠防振墊塊是否脫落或破裂，如果脫落請加上墊片并加以緊固，如有破裂，請及時更換； 或者地盤下面三角盤有一個角沒安裝磨具產生不平衡，發生振動請及時更換磨具。在使用過程中請將磨石用螺絲卡緊，以免工作中打飛出地盤，請注意安全。Wheel overload in work for a period of time, if not found, you can release the frame size screws, adjusting well belt adjusting screw; at work often automatic power, please check the wiring whether GB 4 square line, and the lines to be completely opened, the disc can not be together, in 2 leakage protection switch which has a white connection line, unplug check whether the firm connection. 5, if the belt is loose, the motor rotation, but site don't turn, may is the belt loose, please open the front cover to install the belt wheel. The machine if there is vibration, please check the disc rubber anti vibration cushion block is off or broken, if you fall off, please add gasket and tight Solid, such as rupture, please timely replacement; or site below the triangular disc has a angle did not install the abrasive resulting in the unbalance, vibration, please timely replacement of abrasives. In the use of process in the stone with a screw clamping, lest work hit fly out of site, please pay attention to safety.
聯系人（P.I.C）：王林

手機(Cel)：   18266772024

傳真（Fax）：  0537-8705656

QQ（QQ）：   2952738087

座機（Tel）：  0537-3628056

郵箱（E-mal）：2952378087@qq.com

網站（Web）： http://www.longsongjixie.com

地址：山東省濟寧市任城區府河?xùn)|路26號（銷售科三部）；山東省濟寧市金鄉縣北大街69號（銷售科一部）

濟寧市金鄉工業園07倉庫（龍松配貨中心）；濟寧市緡城政建工業園質量監察大樓龍松科室（技術科）